Home > ELECTRICAL > LIGHTING & CEILING FANS > RECESSED LIGHTING > RECESSED LIGHT HOUSING
Sort By:
Page of 1
Halo H7ICT Recessed Housing Halo H750RICAT Remodel Recessed Housing Halo H5ICAT Recessed Housing
"For use with 120 volt Incandescent lamps. Aluminum construction for greater heat dissipation. For installations where housing will be in direct contact with ceiling insulation. Integral thermal protector guards against misuse of insulation materials and improper lamping. Adjustable socket bracket assures proper and consistent lamp positing. Junction box is listed for through branch circuit wiring and has seven 1/2"" knockouts. Slide-N-Slide connectors allow non-metallic sheathed cable to be installed without removing knockouts. Pre-installed captive bar hangers allow housing to be positioned at any point within a 24"" joist span. Can be field shortened for 12"" joist.  Installation: 7-1/2"" height allows use in 2 x 8 joist construction. Housing accommodates ceilings up to 2"" thick. Requires 6-1/2"" ceiling opening. Listings: UL Damp Locations. UL Feed Through. UL Listed for direct contact with insulation. CSA Certified. IP Rated." The H750RICAT is a dedicated LED Remodel housing for use with Halo H7 Collection 600 900 Series LED modules. The H750RICAT is designed for remodel into insulated ceilings and can be in direct contact with ceiling insulation. This AIR-TITE? housing design prevents airflow between attic and living areas and saves on both heating and air conditioning costs. The H750RICAT LED connector system provides high efficiency code compliance when used with Halo H7 Collection 600 and 900 Series LED modules. The Halo H5 Series is designed to accommodate smaller sized PAR20 and PAR30 halogen lamps. The wide variety of trims available allows a number of different lighting effects to be created with one basic housing. The H5ICAT is designed for use in insulated ceiling applications. This is an Air-Tite? housing and may be used to meet restricted air flow requirements.
Halo H7 Recessed Housing Halo H7ICAT Recessed Housing Halo H7 Remodel Recessed Housing
The H7 recessed housing is the standard in the industry for both commercial and residential applications. The wide variety of trims available allows a number of different lighting effects to be created with one basic housing. The H7T is for use in non-insulated ceilings. If ceiling insulation is present, it must be kept 3 in from all sides of housing. The H7 recessed housing is the standard in the industry for both commercial and residential applications. The wide variety of trims available allows a number of different lighting effects to be created with one basic housing. H7ICAT is for installations where the housing will be in direct contact with insulation and also meet restricted air flow requirements. The H7 recessed housing is the standard in the industry for both commercial and residential applications. The wide variety of trims available allows a number of different lighting effects to be created with one basic housing. The H7RT is suited for use in non-insulated existing ceilings. Housing slips through opening in ceiling. If ceiling insulation is present, it must be kept 3 in from all sides of housing.
Halo H7 Remodel Recessed Housing Halo H99TAT Recessed Housing Cooper Lighting H7RICAT Recessed Lighting Housing
The H7 family of recessed housings are the standard in the industry for both commercial and residential applications. The wide variety of trims available allows a number of different lighting effects to be created with one basic housing. The H7RICT is designed for installations where the housing will be in direct contact with insulation. H7RICT may be converted into Air-Tite? installation when used with Air-Tite? trims. The H99TAT is a small aperture Non-IC AIR-TITE? housing for providing accent and task lighting. The H99TAT is designed for use in non-insulated ceiling or for insulated ceilings but insulation must be kept 3 in from all sides of the housing. Non-IC Housing is AIR-TITE? but insulation must be kept 3 in away from all sides of housing. The H7 family of recessed housings are the standard in the industry for both commercial and residential applications. The wide variety of trims available allows a number of different lighting effects to be created with one basic housing. The H7RICAT housing is designed for installations where the housing will be in direct contact with insulation and also meet restricted air flow requirements.
REC HSG LN VOLTAGE 6IN        Halo H99ICAT Recessed Housing Halo H645IC Recessed Housing
For use in insulated ceilings. No trim. Requires 1 x E26 medium base bulb (not included). 7-1/2 in W x 7-1/2 in H. The H99ICAT is a small aperture IC AIR-TITE? housing for accent and task lighting. It is designed for use in insulated ceilings where it will be in direct contact with insulation. It is an AIR-TITE? housing designed to prevent air flow between living spaces and unconditioned areas. "Designed for sloped ceiling installations for ceilings from 2/12 to 12/12 pitch. The socket mechanism allows the lamp to be aimed straight down regardless of ceiling pitch. Lamp socket and trim can be adjusted 20 degrees laterally for compound slope ceilings or to compensate for off axis aiming. Air-tite fixture sealed and gasketed to prevent airflow between attic and living areas. For installations where housing will be in direct contact with ceiling insulation. Integral thermal protector guards against misuse of insulation materials and improper lamping. Junction box is listed for through branch circuit wiring and has seven 1/2"" knockouts and four Romex knockouts with integral strain relief. Plaster frame includes locking screw for hanger bars and cut outs for crimping hanger bars into position. Pre-installed captive bar hangers allow housing to be positioned at any point within a 24"" joist span. Can be field shortened for 12"" joist. Installation: 7-3/8"" height allows use in 2 x 8 joist construction.  Housing accommodates ceilings up to 1-1/4""  thick. Requires 6-1/2"" ceiling opening. Listings: UL Damp Locations. UL Feed Through. UL Listed for direct contact with insulation. CSA Certified. IP Rated."
Halo H272ICAT Single Wall Recessed Housing Halo H5RICAT Remodel Recessed Housing Halo H27T Shallow Recessed Housing
Energy Star Qualified, California Title 24 compliant 6 in recessed fixture for insulated ceilings and can be in direct contact with ceiling insulation. AIRTITE housing design prevents airflow between attic and living areas and saves on both heating and air conditioning costs. The Halo H5 Series is designed to accommodate smaller sized PAR20 and PAR30 halogen lamps. The wide variety of trims available allows a number of different lighting effects to be created with one basic housing. The H5 trim size makes the H5RICAT the right choice for applications where dramatic yet inconspicuous lighting is required in an existing ceiling. This is an AIR-TITE? housing and may be used to meet restricted air flow requirements. "For installations in non-insulated ceilings or where insulation can be kept 3"" from housing. Integral thermal protector guards against misuse of insulation materials and improper lamping. Adjustable socket bracket allows the use of different lamp types and sizes as well as proper and consistent lamp positing. Junction box is listed for through branch circuit wiring and has seven 1/2"" knockouts and four Romex knockouts with integral strain relief. Plaster frame includes locking screw for hanger bars and cut outs for crimping hanger bars into position. Pre-installed captive bar hangers allow housing to be positioned at any point within a 24"" joist span and can be field shortened for 12"" joist. Installation: 5-1/2"" height allows use in 2 x 6 joist construction.  Housing accommodates ceilings up to 2"" thick. Requires 6-1/2"" ceiling opening. Ring fixture not included. Listings: UL Damp Locations. UL Feed Through. CSA Certified. IP Rated."